Crestron AMP-8150 – Tek bir 1RU form faktöründe köprüleme, Lo-Z ve Hi-Z uygulama

Tek bir 1RU form faktöründe köprüleme, Lo-Z ve Hi-Z uygulamalarını destekleyen sağlam ve verimli amplifikasyon.

Stok kodu: AMP-8150 Kategoriler:

Tek bir 1RU form faktöründe köprüleme, Lo-Z ve Hi-Z uygulamalarını destekleyen sağlam ve verimli amplifikasyon.

Teknik Özellikler

Ethernet 10/100 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, TCP/IP, UDP/IP, CIP, DHCP, SSL, SSH, SFTP (SSH File Transfer Protocol)
USB Device USB device port for computer console (setup)
Input Signal Types Balanced or unbalanced analog line-level
Output Signal Types 4/8 Ohm; 70 Volt direct-coupled (AMP-8150 only); 100 Volt direct-coupled (AMPI-8150 only)
Output Power, AMP-8150 150 Watts per channel @ 4-8 Ohms or 70 Volts nominal; 300 Watts per bridged pair of channels @ 8 Ohms
Output Power, AMPI-8150 150 Watts per channel @ 4-8 Ohms or 100 Volts nominal; 300 Watts per bridged pair of channels @ 8 Ohms
Frequency Response 20 Hz to 20 kHz ±0.5 dB at 1 Watt, 4-8 Ohms; 200 Hz to 20 kHz ±0.5 dB at 1 Watt, 70/100 Volts
High Pass Filter -3 dB @ 80 Hz, 12 dB per octave in 70V or 100V mode
THD+N <0.1% @ 1 kHz at 3 dB below clipping
S/N Ratio >103 dBA, 20 Hz to 20 kHz
Channel Separation >70 dB
Input Sensitivity 1.23 Vrms, +4 dBu (balanced) for full rated output power
Fault Protection Over Current: Protects each channel individually against an excessive speaker load or shorted speaker line; DC Offset: Protects each channel and speaker line against DC voltages sensed at each output; Over Temperature: Protects the amplifier power supply and each channel against overheating due to poor ventilation or excessive temperature; Under Voltage: Protects the amplifier if the internal power supply voltage is below tolerance due to excessive output levels or insufficient line voltage; Note: All faults report to the control system, and indicate on the front panel and in the software tool.
Output Relays Disconnects the speaker line at each output under fault conditions, and during startup and shutdown
Audio Ramp Ramps each channel’s audio level up to its last used setting after the corresponding output relay has closed following startup or fault recovery; ramp time ˜2 seconds
LINE INPUTS 1 – 8 (8) 3-pin 3.5 mm detachable terminal blocks; Balanced line-level audio inputs; Maximum Input Level: 12.3 Vrms, +24 dBu; Input Impedance: 20k Ohms balanced
SPEAKER OUTPUTS 1 – 8 (8) 2-pin 7.62 mm reversed gender 20A detachable terminal blocks; Power amplifier outputs; Wire Size: Terminals accept up to 12 AWG (3.31 mm²); Note: Output is direct-coupled in all modes for all load types, not transformer isolated
LAN (1) 8-pin RJ45 female; 10Base-T/100Base-TX Ethernet LAN port
100-120V~ 50/60Hz 3A (AMP-8150) (1) IEC 60320 C14 main power inlet; Mates with removable power cord (included)
220-240V~ 50/60Hz 2A (AMPI-8150) (1) IEC 60320 C14 main power inlet; Mates with removable power cord (included)
FUSE: T10AH250V (AMP-8150) Main fuse; 1/4” x 1-1/4”, 10A, time-lag, 250V, ceramic
FUSE: T6AH250V (AMPI-8150) Main fuse; 5 x 20 mm, 6.3A, time-lag, 250V, ceramic
G (1) 6-32 screw; Chassis ground lug
COMPUTER (front) (1) USB Type B female; USB computer console port (for setup only)
PWR (1) Bi-color green/amber LED, indicates operating power supplied from AC line power, amber indicates startup in progress, green indicates normal operation, alternating green/amber indicates absence of a network connection
RESET (1) Recessed pushbutton, restores last saved settings
STATUS, FAULT 1 – 8 (8) Red LEDs, each indicates an under-voltage fault condition on the corresponding channel
STATUS, CURRENT 1 – 8 (8) Blue LEDs, each indicates an over-current fault condition on the corresponding output
STATUS, DC 1 – 8 (8) Blue LEDs, each indicates a DC offset fault condition on the corresponding channel
STATUS, THERM 1 – 8 (8) Blue LEDs, each indicates an over-temperature fault condition on the corresponding channel
STATUS, 70V 1 – 8 (AMP-8150 only) (8) Blue LEDs, each indicates the corresponding channel is configured for 70 Volt operation
STATUS, 100V 1 – 8 (AMPI-8150 only) (8) Blue LEDs, each indicates the corresponding channel is configured for 100 Volt operation
VU 1 – 8 (8) 5-segment LED bar graph audio level meters for each corresponding output; each contains (4) blue LEDs for -40dB, -30dB, -20dB, and -10dB, and (1) red LED for CLIP
LINE INPUTS 1 – 8 (rear) (8) Screwdriver-adjustable rotary controls, each adjusts the input attenuation level for the corresponding channel
LAN (rear) (2) LEDs, green LED indicates Ethernet link status, amber LED indicates Ethernet activity
SETUP (rear) (1) Red LED and (1) pushbutton for Ethernet setup, flashes while updating firmware
Power Switch (rear) (1) Rocker switch, turns main power on or off
Main Power (AMP-8150) 3 Amps @ 100-120 Volts AC, 50/60 Hz
Main Power (AMPI-8150) 2 Amps @ 220-240 Volts AC, 50/60 Hz
Power Consumption 253 Watts, all channels driven at 1/8th output power; 70 Watts, all channels idle
Temperature 41° to 104°F (5° to 40°C)
Humidity 10% to 90% RH (non-condensing)
Heat Dissipation 375 BTU/hr, all channels driven at 1/8th output power; 250 BTU/hr, all channels idle
Chassis Metal, variable-speed fan-cooled, vented sides
Front Panel Metal, black finish with polycarbonate label overlay
Mounting Freestanding or 1 RU 19-inch rack-mountable (front rack ears and rear support brackets included)
Height 1.72 in (44 cm)
Width 17.28 in (439 mm); 19.00 in (483 mm) with rack ears
Depth 14.69 in (374 mm)

Kullanım Alanları

  • Kurumsal ve ticari projelerde amplifikatörler çözümü
  • Toplantı odaları, akıllı binalar ve otomasyon sistemlerine entegrasyon
  • Profesyonel kurulum ve merkezi yönetim

Sıkça Sorulan Sorular

Crestron AMP-8150 Türkiye’de satılıyor mu?

Evet. Avelkon, Crestron Türkiye yetkili distribütörüdür. Stok, fiyat ve proje teklifi için bizimle iletişime geçebilirsiniz.

Teknik destek ve kurulum sağlanıyor mu?

Evet, yetkili distribütör olarak ürün seçimi, kurulum ve satış sonrası destek sunuyoruz.

Avelkon, Crestron Türkiye yetkili distribütörüdür. Fiyat ve proje teklifi için iletişime geçin.

Marka

Crestron

Ethernet

10/100 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, TCP/IP, UDP/IP, CIP, DHCP, SSL, SSH, SFTP (SSH File Transfer Protocol)

USB Device

USB device port for computer console (setup)

Input Signal Types

Balanced or unbalanced analog line-level

Output Signal Types

4/8 Ohm; 70 Volt direct-coupled (AMP-8150 only); 100 Volt direct-coupled (AMPI-8150 only)

Output Power, AMP-8150

150 Watts per channel @ 4-8 Ohms or 70 Volts nominal; 300 Watts per bridged pair of channels @ 8 Ohms

Output Power, AMPI-8150

150 Watts per channel @ 4-8 Ohms or 100 Volts nominal; 300 Watts per bridged pair of channels @ 8 Ohms

Frequency Response

20 Hz to 20 kHz ±0.5 dB at 1 Watt, 4-8 Ohms; 200 Hz to 20 kHz ±0.5 dB at 1 Watt, 70/100 Volts

High Pass Filter

-3 dB @ 80 Hz, 12 dB per octave in 70V or 100V mode

THD+N

<0.1% @ 1 kHz at 3 dB below clipping

S/N Ratio

>103 dBA, 20 Hz to 20 kHz

Channel Separation

>70 dB

Input Sensitivity

1.23 Vrms, +4 dBu (balanced) for full rated output power

Fault Protection

Over Current: Protects each channel individually against an excessive speaker load or shorted speaker line; DC Offset: Protects each channel and speaker line against DC voltages sensed at each output; Over Temperature: Protects the amplifier power supply and each channel against overheating due to poor ventilation or excessive temperature; Under Voltage: Protects the amplifier if the internal power supply voltage is below tolerance due to excessive output levels or insufficient line voltage; Note: All faults report to the control system, and indicate on the front panel and in the software tool.

Output Relays

Disconnects the speaker line at each output under fault conditions, and during startup and shutdown

Audio Ramp

Ramps each channel’s audio level up to its last used setting after the corresponding output relay has closed following startup or fault recovery; ramp time ˜2 seconds

LINE INPUTS 1 – 8

(8) 3-pin 3.5 mm detachable terminal blocks; Balanced line-level audio inputs; Maximum Input Level: 12.3 Vrms, +24 dBu; Input Impedance: 20k Ohms balanced

SPEAKER OUTPUTS 1 – 8

(8) 2-pin 7.62 mm reversed gender 20A detachable terminal blocks; Power amplifier outputs; Wire Size: Terminals accept up to 12 AWG (3.31 mm²); Note: Output is direct-coupled in all modes for all load types, not transformer isolated

LAN

(1) 8-pin RJ45 female; 10Base-T/100Base-TX Ethernet LAN port

100-120V~ 50/60Hz 3A (AMP-8150)

(1) IEC 60320 C14 main power inlet; Mates with removable power cord (included)

220-240V~ 50/60Hz 2A (AMPI-8150)

(1) IEC 60320 C14 main power inlet; Mates with removable power cord (included)

FUSE: T10AH250V (AMP-8150)

Main fuse; 1/4” x 1-1/4”, 10A, time-lag, 250V, ceramic

FUSE: T6AH250V (AMPI-8150)

Main fuse; 5 x 20 mm, 6.3A, time-lag, 250V, ceramic

G

(1) 6-32 screw; Chassis ground lug

COMPUTER (front)

(1) USB Type B female; USB computer console port (for setup only)

PWR

(1) Bi-color green/amber LED, indicates operating power supplied from AC line power, amber indicates startup in progress, green indicates normal operation, alternating green/amber indicates absence of a network connection

RESET

(1) Recessed pushbutton, restores last saved settings

STATUS, FAULT 1 – 8

(8) Red LEDs, each indicates an under-voltage fault condition on the corresponding channel

STATUS, CURRENT 1 – 8

(8) Blue LEDs, each indicates an over-current fault condition on the corresponding output

STATUS, DC 1 – 8

(8) Blue LEDs, each indicates a DC offset fault condition on the corresponding channel

STATUS, THERM 1 – 8

(8) Blue LEDs, each indicates an over-temperature fault condition on the corresponding channel

Değerlendirmeler

Henüz değerlendirme yapılmadı.

“Crestron AMP-8150 – Tek bir 1RU form faktöründe köprüleme, Lo-Z ve Hi-Z uygulama” için yorum yapan ilk kişi siz olun

E-posta adresiniz yayınlanmayacak. Gerekli alanlar * ile işaretlenmişlerdir

Scroll to Top