Crestron HD-PS622 — 8×2 4K60 4:4:4 HDR Sunum Sistemi

Matris değiştirme ve kullanıma hazır işlevselliğe sahip, yüksek performanslı, rafa monte edilebilir 4K60 4:4:4 sunum sistemi. Altı HDMI® ve iki DM® Essentials girişi, 4K60 ölçekleyicili iki çift yansıtılmış HDMI ve DM Essentials çıkışı ve analog ses girişleri ve çıkışları sağlar. HDR (Yüksek Dinamik

Stok kodu: HD-PS622 Kategoriler:

Matris değiştirme ve kullanıma hazır işlevselliğe sahip, yüksek performanslı, rafa monte edilebilir 4K60 4:4:4 sunum sistemi. Altı HDMI® ve iki DM® Essentials girişi, 4K60 ölçekleyicili iki çift yansıtılmış HDMI ve DM Essentials çıkışı ve analog ses girişleri ve çıkışları sağlar. HDR (Yüksek Dinamik Aralık) ve Dolby Vision® video formatları, ses karıştırma, gelişmiş EDID yönetimi, XiO Cloud® bağlantısı ve kurumsal düzeyde güvenlik desteğini içerir.

Öne Çıkan Özellikler

  • 4K60 4:4:4 dijital AV sunum sistemi
  • HDR10, HDR10+ ve Dolby Vision® video formatları
  • Otomatik geçişli altı HDMI® ve iki DM® Essentials girişi
  • DM Essentials çıkışlarıyla yansıtılmış iki HDMI çıkışı
  • DM Essentials çıkışlarının HDBaseT® sertifikası
  • Her yansıtılmış çıkış için 4K60 4:4:4 video ölçekleyici
  • Kullanıma hazır işlevsellik
  • Kurumsal düzeyde güvenlik
  • Ekranda gösterim için metin yer paylaşımı, görüntü yer paylaşımı ve arka plan resmi
  • EDID yönetimi
  • HDCP 2.3 uyumluluğu
  • Ses yerleştirme ve ayırma ile ses karıştırma
  • 100BASE-TX/1000BASE-T Ethernet bağlantısı
  • USB güç bağlantı noktası
  • Uyumlu DM Essentials alıcılarıyla kullanıldığında CEC, IR veya RS-232 aracılığıyla cihaz kontrolü

Teknik Özellikler

Switcher 8×2 auto-switching or manual, audio-follows-video, Crestron Auto-Locking® and QuickSwitch HD™ technologies
Scaler (mirrored HDMI and DM Essentials outputs) 4K60 4:4:4 video scaler with motion-adaptive deinterlacing, intelligent frame rate conversion; Deep Color support; HDR10, HDR10+, and Dolby Vision support; content-adaptive noise reduction; and 3:2/2:2 pull-down detection and recovery
Input Signal Types HDMI (Dual-Mode DisplayPort interface compatible 3 ), DM Essentials
Output Signal Types HDMI, DM Essentials, and HDBaseT with HDR10, HDR10+, and Dolby Vision pass-through support, Deep Color support, and 4K60 4:4:4 support (DVI compatible 4 )
Copy Protection HDCP 2.3
Audio Inputs Two mono 1-channel MIC/LINE inputs Six mono 1-channel LINE inputs One stereo 2-channel LPCM audio extracted from the selected HDMI or DM Essentials input source
Audio Outputs One mirrored HDMI 1 and DM Essentials 1 audio output One mirrored HDMI 2 and DM Essentials 2 audio output One AUX 1 output, stereo 2-channel One AUX 2 output, stereo 2-channel
Analog-to-Digital Conversion 24-bit 48 kHz
Digital-to-Analog Conversion 24-bit 48 kHz
Formats Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS, DTS-ES, DTS 96/24, DTS HD High Res, DTS-HD Master Audio, DTS:X, LPCM up to 8 channels
Input Signal Type Mono analog
Gain Range -10 dB to +10 dB in 1 dB increments
Phantom Power +48 VDC, 12 mA, enable or disable per channel
Mute Enable or disable per channel
Balanced Line Input Level 4 Vrms
Unbalanced Line Input Level 2 Vrms
Line Input Impedance >10k ohms
Output Signal Type HDMI
Source Gain -80 dB to +20 dB adjustment range, plus Mute
Volume Control -80 dB to +20 dB adjustment range, plus Mute, Mono, and Stereo
Delay 0 to 150 ms adjustment range
Output Signal Type/Format Stereo 2-channel
Frequency Response ±0.5 dB, 20 Hz to 20 kHz
THD+N <0.005%, 1 kHz, 4 Vrms
S/N Ratio >95 dB, 4 Vrms, 20 Hz to 20 KHz, A‑weighted
Crosstalk >90 dB, 1 KHz, for multiple inputs only
Stereo Separation >80 dB, 20 Hz to 20 kHz
Ethernet (2) LEDs on RJ-45 LAN connector. Link status LED: Green indicates that a 100BASE-TX link is established. Amber indicates that a 1000BASE-T link is established. Ethernet activity LED: Flashing amber indicates Ethernet activity.
USB For firmware loading and configuration management and to power a USB powered device
HDMI HDCP 2.3, EDID, CEC
DM Essentials (2) LEDs on RJ-45 DM Essentials connectors. Green indicates that a DM Essentials link is established. Flashing amber indicates non-HDCP video and solid amber indicates HDCP video.
HDBaseT HDCP 2.3
MIC/LINE CH1-CH2 (2) 3-pin 3.5 mm detachable terminal blocks; Balanced mono microphone/line audio inputs
LINE INPUT CH3-CH8 (6) 3-pin 3.5 mm detachable terminal blocks; Balanced mono line-level audio inputs
AUX OUT 1-2 (2) 5-pin 3.5 mm detachable terminal blocks; Balanced stereo line-level audio outputs; Output Impedance: <200 Ohms; Maximum Output Level: 4 Vrms balanced
HDMI INPUTS 1-6 (6) 19-pin Type A connector, female; HDMI digital video/audio input (DVI and Dual-Mode DisplayPort interface compatible 3 )
DM INPUTS 7-8 (2) 8-pin RJ-45 yellow connectors, female, shielded; DM Essentials input ports for connection to DM Essentials transmitters 5
DM OUTPUT 1 (1) 8-pin RJ-45 blue connector, female, shielded; DM Essentials output port (HDBaseT standard compliant) for connection to a DM Essentials receiver, DMPS Essentials switcher, or HDBaseT device 6 ; Mirrored with HDMI OUTPUT 1
HDMI OUTPUT 1 (1) 19-pin Type A connector, female; HDMI digital video/audio output (DVI compatible 4 ); Mirrored with DM OUTPUT 1
DM OUTPUT 2 (1) 8-pin RJ-45 blue connector, female, shielded; DM Essentials output port (HDBaseT standard compliant) for connection to a DM Essentials receiver, DMPS Essentials switcher, or HDBaseT device; 6 Mirrored with HDMI OUTPUT 2
HDMI OUTPUT 2 (1) 19-pin Type A connector, female; HDMI digital video/audio output (DVI compatible 4 ); Mirrored with DM OUTPUT 2
LAN (1) 8-pin RJ-45 connector, female; 100BASE-TX/1000BASE-T Ethernet port
100-240VAC 1.8-0.7A 50/60 Hz (1) IEC 60320 C14 mains power inlet; Mates with removable power cord, included
G (1) 6-32 screw, chassis ground lug
SERVICE (1) USB 2.0 Type A connector, female; For firmware loading and configuration management; Can also provide up to 5 V 500 mA power to a USB powered device
PWR (1) LED. Amber indicates that the device is booting. Green indicates that the device is operational.
AUTO (1) Push button to enable or disable automatic switching and (1) green LED to indicate that automatic switching is enabled.
SETUP (1) Red LED and (1) push button for display of IP address on connected HDMI and DM Essentials outputs
INPUT 1-8 (8) Push buttons for manual input selection and (8) LEDs. Green indicates that the corresponding input is routed to an output. Amber indicates that a source is detected at the corresponding input but is not routed to an output.
OUTPUT 1-2 (2) Push buttons for manual output selection and (2) LEDs. Green indicates that a display or other destination device is detected and the corresponding output is transmitting video. Amber indicates that a display or other destination device is detected but no video is routed to the corresponding output.
FOLLOW (1) Push button to enable or disable Follow Output mode and (1) LED. Green indicates that Follow Output mode is enabled, which causes the selected HDMI or DM Essentials input to be routed to HDMI and DM Essentials outputs 1 and 2 simultaneously.
Mains Power 100-240VAC 1.8-0.7A 50/60 Hz
Power Consumption 72 W typical
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% RH (non‑condensing)
Heat Dissipation 164 BTU/hr typical
Acoustic Noise 32 dBA typical
Chassis Metal, black finish, vented sides
Mounting 1 RU 19-inch rack-mountable (rack ears included)
Height 1.72 in. (44 mm)
Width 17.33 in. (441 mm) without rack ears 19.00 in. (483 mm) with rack ears (included)
Depth 10.82 in. (275 mm)
Regulatory Model M202004002
DM-CBL-ULTRA DM® Ultra Cable DM-CBL-8G DM 8G® Cable or CAT5e (UTP) or Higher

Kullanım Alanları

  • Kurumsal ve ticari projelerde switcher (matris) çözümü
  • Toplantı odaları, akıllı binalar ve otomasyon sistemlerine entegrasyon
  • Profesyonel kurulum ve merkezi yönetim

Sıkça Sorulan Sorular

Crestron HD-PS622 Türkiye’de satılıyor mu?

Evet. Avelkon, Crestron Türkiye yetkili distribütörüdür. Stok, fiyat ve proje teklifi için bizimle iletişime geçebilirsiniz.

Teknik destek ve kurulum sağlanıyor mu?

Evet, yetkili distribütör olarak ürün seçimi, kurulum ve satış sonrası destek sunuyoruz.

Avelkon, Crestron Türkiye yetkili distribütörüdür. Fiyat ve proje teklifi için iletişime geçin.

Marka

Crestron

Switcher

8×2 auto-switching or manual, audio-follows-video, Crestron Auto-Locking® and QuickSwitch HD™ technologies

Scaler (mirrored HDMI and DM Essentials outputs)

4K60 4:4:4 video scaler with motion-adaptive deinterlacing, intelligent frame rate conversion; Deep Color support; HDR10, HDR10+, and Dolby Vision support; content-adaptive noise reduction; and 3:2/2:2 pull-down detection and recovery

Input Signal Types

HDMI (Dual-Mode DisplayPort interface compatible 3 ), DM Essentials

Output Signal Types

HDMI, DM Essentials, and HDBaseT with HDR10, HDR10+, and Dolby Vision pass-through support, Deep Color support, and 4K60 4:4:4 support (DVI compatible 4 )

Copy Protection

HDCP 2.3

Audio Inputs

Two mono 1-channel MIC/LINE inputs Six mono 1-channel LINE inputs One stereo 2-channel LPCM audio extracted from the selected HDMI or DM Essentials input source

Audio Outputs

One mirrored HDMI 1 and DM Essentials 1 audio output One mirrored HDMI 2 and DM Essentials 2 audio output One AUX 1 output, stereo 2-channel One AUX 2 output, stereo 2-channel

Analog-to-Digital Conversion

24-bit 48 kHz

Digital-to-Analog Conversion

24-bit 48 kHz

Formats

Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS, DTS-ES, DTS 96/24, DTS HD High Res, DTS-HD Master Audio, DTS:X, LPCM up to 8 channels

Input Signal Type

Mono analog

Gain Range

-10 dB to +10 dB in 1 dB increments

Phantom Power

+48 VDC, 12 mA, enable or disable per channel

Mute

Enable or disable per channel

Balanced Line Input Level

4 Vrms

Unbalanced Line Input Level

2 Vrms

Line Input Impedance

>10k ohms

Output Signal Type

HDMI

Source Gain

-80 dB to +20 dB adjustment range, plus Mute

Volume Control

-80 dB to +20 dB adjustment range, plus Mute, Mono, and Stereo

Delay

0 to 150 ms adjustment range

Output Signal Type/Format

Stereo 2-channel

Frequency Response

±0.5 dB, 20 Hz to 20 kHz

THD+N

<0.005%, 1 kHz, 4 Vrms

S/N Ratio

>95 dB, 4 Vrms, 20 Hz to 20 KHz, A‑weighted

Crosstalk

>90 dB, 1 KHz, for multiple inputs only

Stereo Separation

>80 dB, 20 Hz to 20 kHz

Ethernet

(2) LEDs on RJ-45 LAN connector. Link status LED: Green indicates that a 100BASE-TX link is established. Amber indicates that a 1000BASE-T link is established. Ethernet activity LED: Flashing amber indicates Ethernet activity.

USB

For firmware loading and configuration management and to power a USB powered device

HDMI

HDCP 2.3, EDID, CEC

Değerlendirmeler

Henüz değerlendirme yapılmadı.

“Crestron HD-PS622 — 8×2 4K60 4:4:4 HDR Sunum Sistemi” için yorum yapan ilk kişi siz olun

E-posta adresiniz yayınlanmayacak. Gerekli alanlar * ile işaretlenmişlerdir

Scroll to Top